|
| |
Satin Sport Kote®
Water-Based Urethane Wood
Finish (228SF)
Features
 |
Single-component formula means no pot life and no mess. Finish is useable
the next day if more coats are desired. |
|
Contains reactive polymers that offer durability and appearance equal or
greater than oil-modified products. |
|
Excellent black mark, scuff and soil resistance. |
| One
hour dry time between coats under normal conditions. Only 24 hour
down time. |
|
Uniquely restorable unlike traditional wood finishes. |
|
Suitable for oak, maple and parquet floors. |
| Large
area coverage – up to 1,000 sq. ft. per gallon.
|
Properties*
|
Type - Urethane/Acrylic Blend |
|
Form - Opaque Liquid |
|
Odor - Bland |
|
Color - Off-White |
|
Dried Film Color - Colorless |
|
Weight per
Gallon
- 8.65 Lbs. |
|
pH - 7.0-8.0 |
|
Floor Solids - 29% |
|
60° Gloss
- < 30 |
|
Storage Stability - Up To 1 Year, Unopened |
|
Freeze/Thaw - Passes 3 Cycles |
|
Slip-Resistance -
UL Classified |
|
V.O.C.
- <300 gm/l |
*
Properties are typical and subject to usual manufacturing tolerances.
General Directions**
-
PREPARE FLOOR: NOTE: This finish is not designed for
application to bare wood floors. Use only on previously sealed surfaces.
SCRUB AND RECOAT: Dust mop floor and remove all chewing gum and
labels. Clean floor with a 8 ounce per gallon dilution of
Citrus Scrub ‘N Shine
(#525). Screen with a 120 grit screen, black or brown pad to sufficiently
roughen floor. Tack or rinse the floor with
Nu-Tral Cleaner (#507)
until all residue has been removed.
NOTE: Test previously coated floor in an inconspicuous area before
recoating to determine compatibility with existing finish. Apply 2 or 3 coats
of finish. See finish application instructions below.
-
APPLY
FINISH:
Mix gently before using. Apply at a rate of 800-1000 square feet per gallon.
Use a clean, synthetic applicator. Apply thin, even coats with the grain of
the wood. Allow a dry time of at least 1 hour between coats. Humid conditions
will necessitate longer dry time. After the first coat has dried, apply a
second coat. It may be necessary to screen the first coat if grain raising has
occurred or it has dried longer than 4 hours. If so, screen the floor with a
previously used 120 grit screen or brown or black pad. Always vacuum and tack
thoroughly after screening.
NOTE: Do not pour unused finish back into original container. For
best results, use product within 1 year of purchase date.
-
MAINTAIN
DAILY:
Dust mop at least daily, or more as required, to keep floor dust and dirt
free. Damp mop spills, salt residue, etc. with Nu-Tral Cleaner and a
thoroughly wrung mop.
-
MAINTAIN WEEKLY: If soil conditions are heavy, auto-scrub
weekly with red pads and a 2 ounce per gallon dilution of Nu-Tral Cleaner.
Refer to the Wood Floor Care Wall Chart or Manual for further details.
-
RESTORATION: Dust mop floor. Auto-scrub with red pads with an
8 ounce per gallon dilution of Citrus Scrub ‘N Shine. Then dry burnish with
recommended pad.
** See
label directions and MSDS for complete usage and safety instructions.
Application Hints
- Satin
Sport Kote® should be gently mixed before application.
- During
application, make sure air handlers are OFF and doors are closed to eliminate
flash drying. After the application is complete and the finish has skinned
over, ventilation can be turned back on.
- Satin
Sport Kote® can be applied over most existing finishes including
oil-modified products. If uncertain, test in a small, inconspicuous area for
compatibility first.
- Under
high humidity, dry times for Satin Sport Kote® will vary greatly.
Do not apply a second coat if the first coat is still tacky.
- Two
coats is usually sufficient on recoats. If a third coat is desired, make sure
the previous coats are thoroughly dry before applying product.
Packaging Specifications
|
Package
|
Sizes
Available
|
UPC Codes
|
Pack
Size
(inches)
|
Cube
(ft.)
|
Pack
Wt.
(Lbs.)
|
Full
Pallet
|
|
|
2 x 2½ Plastic
Container
|
783366228034
|
14 x
9.5 x 15.25
|
1.17
|
46.11
|
36
|
|
